Catalogue
All products
Search the full range, then narrow it by family, category, model, pressure rating and industry.
Showing all 168 products.
Tube Fittings & Connectors
- O-Seal Male AdapterFluid Controls Double Ferrule O-Seal Male Adapter, OD Tube x Male Straight Thread.
- 45° Male ElbowFluid Controls Double Ferrule Tube Fitting, 45° Male Elbow, Tube OD x Male NPT
- 45° Positionable Male ElbowFluid Controls Double Ferrule Tube Fitting, 45° Positionable Male Elbow, Tube OD x Male Thread.
- Back FerruleThe Fluid Controls Back Ferrule is a key component of a Double-Ferrule tube fitting. It works together with the front ferrule to provide reliable tube gripping and sealing.
- Bulkhead ElbowFluid Controls Double Ferrule Bulkhead Elbow Fitting, Bulkhead Union Elbow, Tube OD x Tube OD
- Bulkhead Female ConnectorFluid Controls Double Ferrule Bulkhead Female Connector, Tube OD x Female Thread
- Bulkhead Male ConnectorFluid Controls Double Ferrule Bulkhead Male Connector, Tube OD x Male Thread
- Bulkhead ReducerFluid Controls Double Ferrule Bulkhead Reducer Fitting, Inch OD Tube x Inch OD Ports
- Bulkhead Reducing UnionFluid Controls Double Ferrule Fitting Bulkhead Reducing Union, Tube OD x Reducing Tube OD.
- Bulkhead UnionFluid Controls Double Ferrule Straight Bulkhead Union Connector, Tube OD x Tube OD
- Butt Weld Pipe ConnectorFluid Controls Double Ferrule Butt Weld Pipe Connector, Tube OD x Pipe.
- Butt Weld Pipe ElbowFluid Controls Double Ferrule Butt Weld Pipe Elbow, Tube OD x Pipe.
- Coupling CapFluid Controls Double Ferrule Coupling Cap
- Female AdapterFluid Controls Double Ferrule Female Adapter, OD Tubes x Female Thread.
- Female Branch TeeFluid Controls Double Ferrule Female Branch Tee, Tube OD x Tube OD x Female Thread.
- Female ConnectorFluid Controls Double Ferrule Female Connector, Tube OD x Female Thread.
- Female ElbowFluid Controls Double Ferrule Female Elbow, Tube OD x Female Thread.
- Female Manometer AdapterFluid Controls Double Ferrule Female Manometer Adapter, OD Tubes x Female Thread.
- Female Manometer ConnectorFluid Controls Double Ferrule Female Manometer Connector, Tube OD x Female Thread.
- Female Run TeeFluid Controls Double Ferrule Female Run Tee, Tube OD x Female Thread x Tube OD.
- Fitting End ClosureFitting End Closure in double-ferrule design for instrumentation tube systems. Available in SS, Brass, and Monel.
- Front FerruleThe Fluid Controls Front Ferrule is a key component of a Double-Ferrule tube fitting. It works together with the Back ferrule to provide reliable tube gripping and sealing.
- Male AdapterFluid Controls Double Ferrule Male Adapter, OD Tube x Male Thread.
- Male Branch TeeFluid Controls Double Ferrule Male Branch Tee, Tube OD x Tube OD x Male Thread.
- Male ConnectorFluid Controls Double Ferrule Male Connector, Tube OD x Male Thread
- Male ElbowFluid Controls Double Ferrule Male Elbow, Tube OD x Male Thread
- Male Run TeeFluid Control Double ferrule Male Run Tee, Tube OD x Male Thread On Run Side x Tube OD
- O-Seal Male ConnectorFluid Controls Double Ferrule O-Seal Male Connector, Tube OD x Male Straight Thread.
- Positionable Branch TeeFluid Controls Double Ferrule Positionable Branch Tee, Tube OD x Tube OD x Male Parallel Thread.
- Positionable Male Branch TeeFluid Controls Double Ferrule Positionable Male Branch Tee, Tube OD x Tube OD x Male Parallel Thread.
- Positionable Male ElbowFluid Controls Double Ferrule Positionable Male Elbow, Tube OD x Male Parallel Thread.
- Positionable Male Run TeeFluid Controls Double Ferrule Positionable Male Run Tee, Tube OD x Male Parallel Thread x Tube OD
- ReducerFluid Controls Double Ferrule Reducer Fitting, Inch OD Tube x Inch OD Ports
- Reducing UnionFluid Controls Double Ferrule Reducing Union Fitting, Tube OD x Reducing Tube OD
- Reducing Union TeeFluid Controls Double Ferrule Reducing Union Tee Fitting, Tube OD x Tube OD x Tube OD
- Socket Weld Tube ConnectorFluid Controls Socket Weld Tube Connector
- Socket Weld Tube ElbowFluid Controls Socket Weld Tube Elbow
- Tube End ClosureFluid Controls Tube End Closure in Double Ferrule Design.
- UnionFluid Controls Double Ferrule Straight Union Connector, Tube OD x Tube OD
- Union CrossFluid Controls Double Ferrule Union Cross, Tube OD x Tube OD x Tube OD x Tube OD.
- Union ElbowFluid Controls Double Ferrule Union Elbow, Tube OD x Tube OD
- Union TeeFluid Controls Double Ferrule Union Tee, Tube OD x Tube OD x Tube OD
- DIN Single Ferrule FittingsFluid Controls Single ferrule instrumentation fittings to DIN standards for hydraulic and railway applications.
- Quick Release ConnectorsQuick-release couplings for rapid connect/disconnect in instrumentation and pneumatic systems.
- FlexiGrip FittingsFlexiGrip fittings are flexible grip connectors for misaligned pipe connections. They are ideal for railway brake piping and vibration-prone installations.
- Swaging Machine & Assembly ToolsSwaging machines and installation accessories for double-ferrule tube fitting assembly.
- Double Ferrule FittingsDouble ferrule instrumentation tube fittings — also called twin ferrule fittings — for leak-tight, reusable connections on instrumentation tubing.
Instrumentation Valves
- Gas Valves for PowerGas valves designed for gas turbine and power generation applications. Engineered for high-temperature, high-cycle gas fuel systems.
- Floating Ball ValvesFloating ball valves for low to medium pressure applications in instrumentation and process systems.
- Two Way Ball Valve – PN 400 Screwed EndsTwo-way instrumentation ball valve rated PN 400, with BSP or NPT screwed ends in sizes 1/4-inch to 2-inch.
- Two Way Ball Valve – PN 200 Screwed EndsTwo-way instrumentation ball valve rated PN 200, with BSP or NPT screwed ends in sizes 1/4-inch to 1-inch.
- Two Way Ball Valve Double Ferrule Tube EndsTwo-way instrumentation ball valve with double-ferrule compression tube ends, metric 6–16 mm and 1/4-inch to 1-inch.
- Two Way Ball Valve Single Ferrule Tube EndsTwo-way instrumentation ball valve with single-ferrule tube ends in L series (PN 250) and S series (PN 400). End connections to DIN 2353, BS 4368 and IS 8805.
- Ball Valve With Flanged Ends – SAE ISO 6162Flanged-end ball valve to SAE ISO 6162, in Code 61 (3000 psi) and Code 62 (6000 psi), sizes 1/2" to 2".
- Ball Valve With Flanged Ends – CETOP RP 63 HFlanged-end ball valve to CETOP RP 63 H, AFNOR 48-054 and ISO 6164, in Code 61 (250 kg/cm²) and Code 62 (400 kg/cm²).
- Multi-Port Gauge ValvesMulti-port gauge valve, designed to give flexibility in positioning gauges or pressure switches.
- Pressure Gauge Pin Valve – Union Bonnet DesignPressure gauge pin valve in union bonnet design, two-way and three-way.
- Pressure Gauge Pin ValvePressure gauge pin valve, two-way and three-way.
- Single Block & Bleed Gauge ValvesNeedle valve with downstream vent, for static pressure gauge and instrument installation — isolation and venting in one body.
- Double Block & Bleed Gauge ValvesFor gauges, switches and pressure transmitters: two valves with a single outlet, combining isolation, calibration and venting.
- Globe Isolation Valve Single Ferrule Tube EndsIsolation and shut-off for liquids, gases and liquid/gas mixtures, with single-ferrule tube connections including ferrule and nut, for metric and inch tube.
- Bolted Bonnet Globe-Type Isolation Valve, Screwed / Socket Weld EndsStandard isolation valve with screwed, socket weld and butt weld ends. Designed to BS 5352 and tested to BS 6755.
- Angle Needle Valves Screwed Bonnet DesignAngle Needle Valves with a screwed bonnet design are engineered for precise flow regulation and dependable shut-off in instrumentation and process systems.
- Needle Valve – Integral Bonnet Screwed EndsAn integral bonnet needle valve features a unified body and bonnet design, offering superior leak prevention, high-pressure resistance, and precise flow control in critical industrial systems.
- Needle Valves Screwed Bonnet Design, Male × Female EndsNeedle Valves with a screwed bonnet design and Male × Female end connections are engineered for precise flow regulation and dependable shut-off in instrumentation and process systems.
- Colour Flow Needle ValveCompact valve with micrometer adjustment for fine throttling, with coloured rings indicating the number of turns open.
- Needle Valve – Integral Bonnet Double Ferrule EndsAn integral bonnet needle valve features a unified body and bonnet design, offering superior leak prevention, high-pressure resistance, and precise flow control in critical industrial systems.
- Needle Valves Screwed Bonnet Design, Female EndsNeedle Valves with a screwed bonnet design and Female × Female end connections are engineered for precise flow regulation and dependable shut-off in instrumentation and process systems.
- Needle Valves Screwed Bonnet Design, Double Ferrule Tube EndsNeedle Valves with a screwed bonnet design and Tube OD end connections are engineered for precise flow regulation and dependable shut-off in instrumentation and process systems.
- Non Return Valve – PN 400 Screwed EndsCheck Valves allow one-way fluid flow and automatically prevent reverse flow. Factory-set cracking pressures with ball or poppet designs ensure reliable, maintenance-free backflow protection.
- Non Return Valve – PN 400 Double Ferrule Tube EndsCheck valve with double-ferrule tube ends. Cracking pressure 0.3–0.5 kg/cm² standard.
- Non Return Valve – PN 400 Pipe / Single Ferrule Tube EndsCheck valve with pipe and single-ferrule tube ends, in L series (PN 250) and S series (PN 400). Cracking pressure 0.3–0.5 kg/cm² standard.
- Compact Non Return Valve Screwed EndsCompact Check Valves provide reliable one-way flow control in a space-saving design. Preset cracking pressures, leak-tight sealing, and durable construction ensure dependable backflow prevention in instrumentation systems.
- Compact Non Return Valve Single Ferrule Tube EndsSealed by a 90° cone with a synthetic packing washer, on single-ferrule tube ends. Cracking pressure 0.3–0.5 kg/cm².
- Non Return Valve – PN 400 Single Ferrule Metric Tube EndsNon return valve with single ferrule metric tube ends, in an L series rated PN 250 and an S series rated PN 400, with a standard cracking pressure of 0.3 to 0.5 kg/cm².
- Compact Non Return Valve Pipe / Single Ferrule Tube EndsCompact non return valve with a BSP pipe end and a single ferrule tube end, sealing on a 90° cone, in an L series rated PN 250 and an S series rated PN 400.
- Isolation Globe Valves For Instruments, Female EndsGlobe isolation valve with female ends for straight shut-off of liquid, gas or vapour, rated 3000#, 6000# and 9000# to Engineers India Ltd. specification 6-52-69 Rev.1.
- High-Pressure Needle ValvesHigh Pressure Needle Valves with a screwed bonnet design are designed for precise flow regulation and dependable shut-off under High Pressures and connections like Threaded, Cone & Thread Fittings.
- Three-Way Switching Service Ball ValveThree-way switching-service ball valve with 180° stem rotation for mixing and changeover duty, panel-mountable, 3 mm to 3/4-inch.
- Four-Way Switching Service Ball ValveFour-way switching-service ball valve with 90° stem rotation and low operating torque, panel-mountable, 3 mm to 3/4-inch.
- Pressure Gauge Pin Valve – Integral Bonnet DesignPressure gauge pin valve in integral bonnet design.
Manifolds
- 5-Valve ManifoldThe 5-valve manifold integrates isolation, equalization, venting, and calibration into one compact unit, maximizing safety, operational flexibility, and maintenance convenience for differential pressure systems.
- 3-Valve ManifoldBuilt for differential pressure applications, the 3-valve manifold combines two isolation valves and an equalization valve into one compact unit, enabling technicians to safely commission, calibrate, and service transmitters.
- 4-Valve ManifoldA 4-valve manifold gives two block, one vent and one equalise valve for DP transmitter installations.
- Three-way pressure instrument manifoldThe screwed three-way manifold: female process, gauge and drain ports in one block, in a straight and a right-angle pattern.
- PTM 1Vent valve on top, isolation valve on the side, with the drain / vent port available at 1/4" or 1/2" NPT.
- PTM 2Isolation and vent valves opposed across the block, with the drain taken on the process side.
- PTM 3Isolation and vent valves opposed across the block, with the drain taken on top rather than on the process side.
- PTM 4Both valves brought out on one side with the vent valve angled, for a hook-up with clearance on three faces.
- PTM 5Both valves taken off the top of the block with the drain on the process side, for hook-ups reached from above.
- PTM 6Vent valve on the side, isolation valve angled off the top and the drain brought out in front.
- Two-Valve Direct MountingPTM 6's valve arrangement on a flanged instrument connection, so the transmitter mounts straight onto the manifold.
- Two-Valve T-TypeThe "T" pattern on a flanged instrument connection, with a 1/2" NPT process port and a 1/4" drain.
- Single Isolate / Vent BlockLow-pressure direct-mounting block for level measurement on atmospheric tanks, with a T-bar isolate handle and an anti-tamper vent handle.
- Block & BleedOne-piece block and bleed on an ASA raised-face flange, bolted straight to the vessel or process pipe for primary isolation.
- Two-Valve Coplanar MountingIntegral coplanar manifold built to assemble onto particular transmitter models, with one isolating valve and one vent valve.
- Remote MountingValves on three sides with screwed connections, for mounting a differential pressure instrument away from the manifold on impulse lines.
- Direct Mounting DM 1All three valves on top with screwed process connections, for direct mounting where a straight valve would foul the instrument.
- Direct Mounting DM 2Flanged body with the valves on three sides and a screwed process connection — DM 1's alternative where the handles need separating.
- Three-Valve T-TypeThe "T" pattern with a screwed process connection, landing direct on the instrument.
- H-TypeFlanged on both the instrument and the process side, so it will mount direct or go remote on oval / kidney flanges.
- Three-Valve Coplanar MountingIntegral coplanar manifold for particular transmitter models — two isolating valves, one equaliser and two plugged vent ports.
- Steam ServiceFor power generating equipment on superheated steam, to boiler regulations, with a butt-weld process connection and an M20 drain.
- Four-Valve Direct MountingDouble isolate / vent block for services where the process fluid must not be contaminated, with a tamper-proof vent handle.
- Direct Mounting, EqualiseDouble isolate / equalise / vent block with a common drain, for general liquid and gas differential pressure measurement.
- Remote Mounting 5 RM1Two isolation valves, one equaliser and two drain / vent valves on separate connections, for remote mounting on impulse lines.
- Remote Mounting 5 RM25 RM1's valve set on a COMMON drain connection with the drain brought out in front.
- Remote Mounting 5 RM3The third remote-mounted five-valve block, with separate drain / vent connections on a different body form to 5 RM1.
- Five-Valve Direct MountingVent valves on the side and the rest on top, angled to clear the instrument, with a screwed process connection.
- Five-Valve T-TypeThe "T" pattern five-valve block, screwed on the process side and flanged on the instrument.
- H-TypeFlanged on both sides with the drain port on one side and an optional test port at the bottom — mounts direct or remote.
- Five-Valve Coplanar MountingIntegral coplanar manifold for particular transmitter models — two isolating valves, one equaliser, two vent valves and two plugged bottom test ports.
- 2-Valve ManifoldFluid Controls Block and Bleed Manifolds (2-Valve Manifolds) are specifically engineered for direct installation with pressure measurement instruments, including pressure transmitters, gauges, and switches.
Double Block & Bleed Valves
Pipe Clamps (DIN)
- Flat Steel Strip U-ClampsFluid Controls Flat steel strip U-clamps for securing tube and pipe runs against vibration.
- Pipe ClipsFluid controls Single pipe clips for lightweight tube and pipe support.
- Standard & Heavy Duty Series ClampsFluid Controls- DIN 3015 standard and heavy-duty series clamps for parallel tube runs under vibration and thermal cycling. • Body materials: Polypropylene/Polyamide. •Top-Bottom plate & Bolts material: SS316, SS304, MS
- U-Bolt ClampsFluid Controls U-bolt clamps for clamping and anchoring pipe to structural supports.
- Twin Series Tube & Pipe ClampsFluid Controls DIN 3015-3 twin series clamps for side-by-side tube and pipe runs in hydraulic and pneumatic systems.
- Channel Mounting RailsChannel mounting rails and 'T' nuts for carrying several DIN 3015 pipe clamps on a single base. DIN 3015 Clamps are also available for mounting directly onto channels using T-nuts.
- Tube & Pipe ClampsSingle-bore DIN 3015 Standard duty & Heavy duty tube and pipe clamps with the four-rib body that damps vibration and holds the line rigid.
SAE & CETOP Flanges
- SAE Code 62 Flange6000 psi series flange adaptor.
- Butt Weld Flange Assemblies – SAE 3000# & 6000#Union (AFU) and half (AFH) flange assemblies with butt weld end connections. ISO 6162-1 & 2. SAE Code 61 (3000 PSI / 210 bar) and Code 62 (6000 PSI / 410 bar).
- Butt Weld Flange Assemblies – Two Piece SystemTwo-piece butt weld flange assemblies for SAE 3000# and 6000# series. ISO 6162-1 & 2.
- Socket Weld Flange Assemblies – SAE 3000# & 6000#Fluid Controls Half (ASH) and union (ASU) flange assemblies with socket weld ends, two-piece design. ISO 6162-1 & 2. SAE Code 61 and Code 62.
- Butt Weld Elbow Flange Connections – SAE 3000# & 6000#Elbow flange connections with (AEBO) and without (AEB) O-ring, butt weld ends. ISO 6162-1 & 2.
- Socket Weld Elbow Flange Connections – SAE 3000# & 6000#Elbow flange connections with (AESO) and without (AES) O-ring, socket weld ends. ISO 6162-1 & 2.
- Butt Weld Flange Assemblies – PN 160 / PN 250 / PN 315Half (FH) and union (FU) flange assemblies with butt weld ends. PN 160, PN 250 & PN 315 ratings. Ref: Avit FA and FK Series.
- CETOP Butt Weld Flange Assemblies – ISO 6164Half (CBH) and union (CBU) CETOP square flanges with butt weld ends. PN-250 Static / PN-160 Dynamic and PN-400 Static / PN-315 Dynamic. ISO 6164.
- CETOP Socket Weld Flange Assemblies – ISO 6164Half (CSH) and union (CSU) CETOP square flanges with socket weld ends. PN-250 Static / PN-160 Dynamic and PN-400 Static / PN-315 Dynamic. ISO 6164.
- Square Flange Assemblies – Socket Weld PN 100 / PN 160 / PN 250Fluid Controls Square flange assemblies with socket weld ends. PN 100, PN 160 & PN 250. Ref: SMS Specification SN 712.
Hoses & Hose Connectors
- Rubber Hose EN 853Steel wire braid hydraulic hose to EN 853 in 1SN, 2SN, 1ST and 2ST types, for medium pressure hydraulic, coolant, water and air lines.
- Rubber Hose EN 854Textile braid hydraulic hose to EN 854 in 1TE, 2TE and 3TE types, rated to 160 bar and suitable for railway braking systems.
- Rubber Hose EN 856Four- and six-spiral steel wire hydraulic hose to EN 856 in 4SP, 4SH, R12 and R13 types, rated 165 to 450 bar.
- Rubber Hose EN 857Compact steel wire braid hydraulic hose to EN 857 in 1SC and 2SC types, rated 88 to 400 bar for narrow installations.
- Rubber Hose SAE J30Single textile reinforced R6 hose to SAE J30, rated 5 bar, for CNG fitted vehicles.
- Corrugated Metallic Hose – Non-BraidedUnbraided annular corrugated stainless steel hose to ISO 10380, 4 to 100 mm, rated 1 to 26 bar for steam, air and high temperature fluids.
- Corrugated Metallic Hose – BraidedBraided annular corrugated stainless steel hose to ISO 10380, 4 to 100 mm, rated 19 to 153 bar for steam, air and high temperature fluids.
- PA HoseLightweight polyamide hose to DIN 73378 and DIN 74324, 1.5 to 14 mm, for pneumatic, hydraulic, fuel and lubrication lines.
- PTFE Hose – UnbraidedSintered PTFE core hose without braiding, 3 to 19 mm, rated 13 to 80 bar for all fluids up to 260°C.
- PTFE Hose – Single Metallic BraidedSintered PTFE core hose with a single 304 stainless steel braid, 3 to 28 mm, rated 44 to 224 bar for all fluids from -54°C to 260°C.
- PTFE Hose – Double Metallic BraidedSintered PTFE core hose with double 304 stainless steel braiding, 3 to 29 mm, rated 60 to 310 bar for all fluids from -54°C to 260°C.
- O-Ring Face Seal Hose ConnectorHose connector terminating in an O-ring face seal end, to ISO 8434-3, SAE J1353, in stainless steel, carbon steel or brass.
- 24° Cone Hose ConnectorHose connector terminating in a 24° cone connector with O-ring and DKO type nut, to ISO 8434-1, DIN 2353, in stainless steel, carbon steel or brass.
- Flanged End Hose ConnectorHose connector terminating in a flanged end, in butt weld and socket weld flange forms, to ISO 6162-1, ISO 6162-2, SAE J518, in stainless steel, carbon steel or brass.
- Metric Stud End Hose ConnectorHose connector terminating in a metric stud end, to ISO 6149, in stainless steel, carbon steel or brass.
- 37° Cone Hose ConnectorHose connector terminating in a 37° cone connector, the JIC pattern, to ISO 8434-2, SAE J514, in stainless steel, carbon steel or brass.
- 60° Cone Hose ConnectorHose connector terminating in a 60° cone connector with O-ring and DKO type nut, to ISO 8434-6, SAE J514, in stainless steel, carbon steel or brass.
- BSPP / BSPT Hose ConnectorHose connector terminating in a BSPP or BSPT threaded end, to ISO 7, ISO 228, in stainless steel, carbon steel or brass.
- NPT / NPTF Hose ConnectorHose connector terminating in an NPT or NPTF threaded end, to ASME B1.20.1, in stainless steel, carbon steel or brass.
- SAE Flange Hose ConnectorHose connector terminating in an SAE flange end, to SAE J518, in stainless steel, carbon steel or brass.
- Metric Hose ConnectorHose connector terminating in a metric threaded end, to BS 3643-1, in stainless steel, carbon steel or brass.
- JIS Cone Hose ConnectorHose connector terminating in a JIS cone connection at 30°, 37°, 45° or 60°, to JIS B2351, JIS B8363, in stainless steel, carbon steel or brass.
- Single Ferrule Hose ConnectorHose connector terminating in a single ferrule compression end, to ISO 8434-1, DIN 2353, in stainless steel, carbon steel or brass.
- Double Ferrule Tube ConnectorHose connector terminating in a double ferrule compression end, to Fluid Controls design, in stainless steel, carbon steel or brass.
Quick Release Couplings
- ISO 7241-A Quick Release Connector – AISO A SeriesQuick release connector to ISO 7241-A in the AISO A series, 1/4" to 2" with BSP or NPT female threads, rated 100 to 315 bar.
- ISO 7241-B Quick Release Connector – AISO B SeriesQuick release connector to ISO 7241-B in the AISO B series, 1/4" to 1" with BSP or NPT female threads, rated 100 to 250 bar.
- DIN Series Quick Release ConnectorQuick release connector to the DIN pattern, 1/4" to 1" with BSP threads only, rated 220 to 350 bar.
- ISO 16028 Flat Face Quick Release ConnectorFlat face quick release connector to ISO 16028, 1/4" to 1" with BSP or NPT female threads, rated 220 to 350 bar.
- ISO 16028 Flat Face Screw Quick Release ConnectorScrew-type flat face quick release connector to ISO 16028, 1/4" to 1" with BSP, NPT or metric threads, rated 500 to 550 bar.
- ISO 14541 Screw Coupling Quick Release Connector – PoppetPoppet-type screw coupling to ISO 14541, 1/4" to 1" with BSP or NPT female threads, rated 250 to 350 bar.
- ISO 14540 High Pressure Screw Coupling – Ball TypeBall-type high pressure screw coupling to ISO 14540, 1/4" and 3/8" with NPT threads, rated 720 bar.
Specialty & Engineered Products
- Instrument Air HeaderInstrument Air Distribution Manifold
- Condensate PotCondensate pots are robust, engineered assemblies designed to collect and maintain condensate at instrument impulse lines, ensuring reliable and accurate pressure/flow measurement in steam and process applications.
- CNG Fuel Application FittingsFluid Controls Specialized fittings for compressed natural gas (CNG) fuel systems in automotive and stationary applications.
- Pressure Hook-upPressure Hook-Ups are pre-engineered assemblies designed for the safe connection, isolation, venting, and accurate measurement of process pressure instruments such as pressure gauges, transmitters, and switches.
- DP Flow Transmitter Hook-UpPre-fabricated hook-up for DP flow transmitters, built around an 'H' type five-valve manifold connected to the orifice plate.
- Hook-Up for Pressure InstrumentsPre-fabricated hook-up for pressure transmitters and gauges, built around a multiport isolation ball or needle valve.